HOME
Innovative Security Products

Home                     Contact Us

Text Box: NEC WT610 and 615 WALL MOUNTING KITS

 

WALL BOOM KIT Code 8240

WHITEBOARD BRACKET KIT Code 8250

SECURITY KIT Code 8260  

 

FITTING INSTRUCTIONS

 

 

These kits are designed to be used together to mechanically achieve a level and square installation prior to commencing digital compensation.  The kits are suitable for boards 54ins to 100ins diagonal.

IF THE PROJECTOR HAS BEEN USED BEFORE RESET TO FACTORY SETTINGS

 

WALL BOOM KIT Code 8240

                                  1         2 

 

  1. Establish the desired position of the interactive whiteboard and mark the top of the board and the centreline of the board on the wall.

    

  1. Headroom. Consult the dimension chart on page 5 ( DIMENSION A) to establish whether there is sufficient headroom to mount the whiteboard in the desired position. For example a 66inch diagonal board requires 700 mm headroom above the top of the board. Adjust position of board if necessary.

 

 

                                     3      4

  1. Attaching the boom to the wall. Using the spirit level extend the centreline vertically and lightly mark on the wall. Consult the chart to establish the height of the bottom of the boom bracket above the top of the board and mark on the wall. ( DIMENSION B )

 

  1. Offer up the boom and mark the fixing holes on the wall.  Ensure that the top flange of the boom is horizontal using the spirit level and fix the boom to the wall using fixings not provided.

 

 

                                   5     6

  1. Attaching the projector to the boom.  Firstly turn the projector upside down on a soft surface and screw the plate to the underside of the projector using M4 screws provided.  The arrow points towards the straight front side.

 

  1. Attach the dip bracket to the projector plate using the three M8 set screws provided and lightly tighten.

 

 

                                    7A    7B

 

  1. Attach the horizon bracket to the end of the boom.  A. For boards 62 ins and under diagonal mount the bracket with the smiley faces towards the wall.  B. For boards 63 ins and over diagonal attach the horizon bracket with the smiley faces pointing into the room.

 

                                                     8

 

  1. Offer the projector, plate and dip bracket up to the horizon bracket on the boom and secure with 4 nr M8 set screws.

 

                                       9A   9B

 

  1. Using the spirit level check the projector plate is level both (A) parallel to the wall and (B) parallel to the boom.  Lightly tighten.

 

              10           11A            11B     

 

  1. Check that the projector is square to the wall by measuring from the bottom front corner of the projector to the wall. Lightly tighten.

 

  1. Consult the chart ( DIMENSION C) to establish the optimum distance between the front of the projector and the wall. Slacken the two securing screws (A) on top of the boom, slide the boom out (B) to achieve the correct distance and lightly lock the screws in place. Recheck that steps 8 to 10 are still aligned.

 

 

WHITEBOARD WALL BRACKET KIT Code 8250

                                 12A  12B

 

  1. Attaching the board brackets to the wall.  (A) Extend the line on the wall marking the top of the board horizontally approx 500mm to the left and right using the spirit level. Fix the wall brackets equidistant from the vertical centreline approximately 800mm apart as shown. (B) Ensure that the top of the brackets are level with each other and that they are both plumb.

 

                          13   14  15

  1. Attach the comb plates to the wall brackets as shown using the M8 set screws. Adjust the plates so that the top corners of both brackets are equidistant from the bottom corners of the projector. Plumb the brackets and lock off.

 

  1. Both the wall frame and the projector should now be square and level and aligned to each other. Take check measurements to ensure that this is the case.

 

 

 

  1. Whiteboard with a top hanging groove. Offer the whiteboard fixing bars to the rear of the board              (usually between 50 and 200mm from the top of the board).   The bar is usually engaged in a groove at the top of the board. If this is the case, locate the bars in the comb plate on the wall bracket and trial hang the board using the top bar only. Relocate to achieve the closest match of the top of the board level with the top of the wall bracket. Locate the bottom bar in a pair of comb grooves best suited to securing the bottom half of the board back to the whiteboard bar. Do not remove the tape from the Velcro strip at this time.

 

  1. Whiteboard with bolt fixings to the rear. Fix the bars to the frame with bolts as shown. If the preformed holes are not at the correct centres it may be necessary to drill custom holes in the bar. New holes are being added to the bars as information is updated. Please advise if our bars do not suit your hole centres together with the model of board. Hang the board on the comb. grooves as shown.

 

  1. Switch on the projector and check the image is as central and as square as possible before commencing digital correction.

 

      At this stage the image should be square on the board.  

 

      If not Check

            1  The factory settings have been reset.

2  The projector is level in both directions ( use spirit level not digital tilt level. Step 9A and 9B)

3  The projector is square to the wall ( use the tape measure. Step 10)

4  The board is plumb ( use the spirit level)

5  The top corners of the board are equidistant from the front corners of the projector. ie the board is parallel to the front of the projector and central ( use the tape measure)

6  When satisfied with the squareness of the image the boom can be slid in and out and the board raised and lowered to achieve the best fit. Lock boom in best position

 

 ONLY NOW COMMENCE DIGITAL CORRECTION

 

Finally remove tape from Velcro and allow adhesive surface to make contact with the rear of the board. If it is necessary to split the Velcro in the future prise apart the two halves with a small screwdriver.

    

  1. Fit the top clip or clips to the wall to prevent the board from being lifted from the brackets. (see large image on front page)

 

SECURITY KIT Code 8260  

  1. Security cable. (A) With the projector in position loop the large stopper end of the security cable around one of the projector handles using the stainless steel plate as shown. Thread the cable down the inside of the boom exiting near the wall.

                    19A   19B  19C

(B) Pass the small stopper through the round section of the keyhole shape in the top flange of the wall boom bracket and slide cable along the parallel part of the keyhole. (C) Secure cable in place by passing hasp of padlock through the round of the keyhole and snap shut.

 

8240     Stub boom and projector plate. Sliding wall boom, horizon bracket, dip bracket, NEC projector plate, 12 M8 x 16 dome bolts, 12 M8 washers, 4 M4 x 10 screws, 4 M4 washers, spirit level, tape measure, 5mm allen key long.

8250     Wall Brackets. 2 wall angles, 2 comb plates, 2 angled bars, 2 top clips, 8 M8 x 16 bolts, 8 M8 washers, 4 pcs Dual lock

8260     Security Kit. 1350mm cable, Stainless steel loop plate, 32 mm padlock

Return to top